HighFlow on an one week holiday, from August 18 till August 25 2020 no shipments!
/////
We are changing our newsletter system! Please (re)subscribe to our newsletter here: HighFlow Newsletter.

WORLDWIDE SHIPPING with GLS, DPD, PostNL & UPS. We ship to every country! Your country not listed? Please contact us.

Thermaltake Pacific M-Pro G1/4 PETG 12mm Fitting - Black - CL-W170-CU00BL-A

 -   - 
List price: 9,95 (8,22 excl tax)
Our price: 7,95 (6,57 excl tax)
You save: 2,00 (20%) (1,65 excl tax)
Price in points: 33 points
Reward points: 1 point
Thermaltake Pacific M-Pro PETG Fittings Installation Guide

Step 1. Slide the compression nut over the tube
Step 2. Install the o-ring
Step 3. Install the packing
Step 4. Install the fitting base on your components
Step 5. Tighten the compression nut 
 

Caution: The O-ring and the packing with a groove on the inside diameter must always be installed towards the top of the compression nut.

Caution
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
  1. To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  2. Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  4. Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup
  1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  4. Fill the reservoir to the top as it will prevent air from going into the pump
  5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  6. Place some paper towels under fittings and joining points to test for leaks.
  7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
  8. Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  9. Coolant might fade over time.
Manufacturer:
Thermaltake

No posts found

Write a review

Customers also bought

 -   - 
4,95 (4,09 excl tax)
 -   - 
8,95 (7,40 excl tax)
 -   - 
12,95 (10,70 excl tax)
 -   - 
9,95 (8,22 excl tax)
 -   - 
7,95 (6,57 excl tax)
 -   - 
2,95 (2,44 excl tax)
 -   - 
14,90 (12,31 excl tax)
 -   - 
232,95 (192,52 excl tax)
 -   - 
8,95 (7,40 excl tax)
 -   - 
2,95 (2,44 excl tax)
 -   - 
19,95 (16,49 excl tax)
 -   - 
4,95 (4,09 excl tax)
 -   - 
14,90 (12,31 excl tax)
 -   - 
12,95 (10,70 excl tax)