Thermaltake Pacific Hard Tube Bending Kit for ID 10mm x OD 12mm Hard Tube - CL-W153-AL00BU-A

 -   - 
Onze prijs: 84,95 (70,21 excl. BTW)
Prijs in waardepunten: 352 punten
Punten verdiend: 7 punten
+
Thermaltake Pacific Hard Tube Bending Kit for ID 10mm x OD 12mm Hard Tube
The new hard tube bending tools offered by Thermaltake are especially designed for ID 10mm x OD 12mm hard tube and provide everything makers needed when considering loop planning. Available in various angles, the laser-marked mandrels are made from solid aluminum and are anodized for maximum durability. In addition, the cutter and reamer guarantee a by eliminating all the hassles during the modding process.
 
Tt LCS Certified
“Tt LCS Certified” is the hallmark that ensures first-class performance from the best features and fitment. A certification exclusive to Thermaltake, it sets the benchmark for all true LCS chassis and is applied only to products that meet our stringent design standards for delivering what hardcore enthusiasts demand. The Tt LCS certification is a way for Thermaltake to designate to all power users the chassis which have been tested for best compatibility with extreme liquid cooling configurations.
 
Various Mandrels for Stylish Bending
Made from solid aluminum and anodized for maximum durability, the mandrels feature polished center line channels that help to maintain the tubes’ round shapes while bending. Bending angles can be chosen from 45°, 90°, 180°, and 360°.
 
Clean and Precise Cut
The cutter can support 1/8” (3 mm) to 1 and 1/4” (32 mm) hard tube and allows users to make perfectly square end cuts. The internal and external reamer is designed to deburr the inner diameter and the outer diameter of the extruded hard tubing. With a silicon cord, kinking is prevented when bending the tube.
 
Pictures above are for reference only.
Versatile Installation
Designed for ID 10 mm x OD 12mm hard tube, the Pacific Hard Tube Bender Kit allows makers to construct aesthetically superior water cooling systems by allocating the tubes and radiators to each particular component and incorporating externally-modular upgrades into their chassis.
Caution
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
  1. To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  2. Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  4. Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup
  1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  4. Fill the reservoir to the top as it will prevent air from going into the pump
  5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  6. Place some paper towels under fittings and joining points to test for leaks.
  7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
  8. Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  9. Coolant might fade over time.
P/N CL-W153-AL00BU-A
Compatibility ID 10mm x OD 12mm hard tube
Material Mandrels :Aluminum
Cord:Silicone
Reamer:Plastic + Steel
Kit Contents 45° & 90° Mandrels x 1
180° Mandrels x 1
360° Mandrels x 1
Cutter x 1
Silicone cord x 1 
Inside-outside Reamer x 1
Fabrikant:
Thermaltake

This kit is not exactly cheap but it is made out of great quality materials and it is complete. Once you have this kit you are ready to start cutting and bending PETG and Acrylic tubes.

Mandrels are alumimun made so no worries about breaking them or damaging them if you blow them with the heatgun when bending tubes. They also have holes to screw them in place for more easy bending or a calculated bending procedure.

The cutting tool is also metallic and cuts tubes easily, effortlessly and precisely.

The deburrer tool is nothing special though, but it gets the job done.

Schrijf een beoordeling

Andere klanten kochten ook

 - 
2,50 (2,07 excl. BTW)
Besparing 75%
 - 
Adviesprijs: 5,95 (4,92 excl. BTW) 1,50 (1,24 excl. BTW) U bespaart: €4,45 (75%) (€3,68 excl. BTW)
0,50 (0,41 excl. BTW)
Besparing 31%
 -   - 
Adviesprijs: 15,95 (13,18 excl. BTW) 10,95 (9,05 excl. BTW) U bespaart: €5,00 (31%) (€4,13 excl. BTW)
 - 
19,95 (16,49 excl. BTW)
 -   - 
3,05 (2,52 excl. BTW)
 -   - 
2,95 (2,44 excl. BTW)
 -   - 
8,95 (7,40 excl. BTW)
 -   - 
15,90 (13,14 excl. BTW)
 -   - 
5,95 (4,92 excl. BTW)
 -   - 
5,05 (4,17 excl. BTW)
 - 
1,50 (1,24 excl. BTW)
 -   - 
3,55 (2,93 excl. BTW)
 - 
2,50 (2,07 excl. BTW)