Bitspower Sedna O11D Lite for LIAN LI O11 DYNAMIC Series
Owners of LIAN LI O11 DYNAMIC Series cases, Bitspower has you covered for your customized reservoir and pump needs with the Bitspower Sedna O11D Lite. While being a perfect fit within this mid-size chassis, this customized reservoir's pump is dissimulated at the back in order to provide an unaltered look to your PC.
With novice modders in mind, Bitspower designed a reservoir that is easy to install while providing a professional look. Equipped with multiple water inlets and outlets to route the water from the radiator to the VGA than the CPU, this customized reservoir also gives you more playroom for the graphics card location with a dual inlet/outlet designed to prevent having to bend more tubes and create a cleaner look to your loop.
The Bitspower Sedna O11D Lite, equipped with Bitspower Digital RGB, is sure to become the center of attention of your case with bright LEDs that are certified by ASUS AURA Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, ASRock Polychrome, BIOSTAR VIVID LED DJ, and Razer Chroma.
LED Color: Digital RGB
LED Strip Management By Bitspower Digital RGB And Certified By ASUS AURA Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, ASRock Polychrome, BIOSTAR VIVID LED DJ and Razer Chroma.
Dimension (L x W x H): 360 x 130 x 41.3 mm
- Lian Li O11 DYNAMIC
- Lian Li PC-O11 Air
- Lian Li O11 Dynamic XL ROG Certified
- Rated voltage: 12V DC
- Power consumption: 9.6W
- Maximum flow: 460±15%L/h
- Noise: ≦24dBA
- PWM: Yes
- Service life: ≦15,000 hours
- Warranty: 2 years
- 1 set of BPTA-WDPO11DTE-K1M
- 4 pcs of BPTA-F06-GS
- 1 pcs of BPTA-EXAIR-GS
- 1 pcs of BPTA-EFW-V2-GS
- 1 set of Mounting Screws/Accessories
If there aren’t enough DRGB headers on the motherboard, you can use the "Bitspower Touchaqua Digital RGB Multi Function Controller", which is available for purchase via the link below: https://www.highflow.nl/modding/leds/led-stations-controllers/bitspower-touchaqua-digital-rgb-multi-function-controller.html?sl=en
I wanna show off, but what's the support I'd need?
The end of power supply is 3PIN. The sequence is +/D/↓ (some motherboards are shown +5V/D/↓, and the plug is like 4PIN but the 3rd PIN is empty). Please plug in the corresponding direction of motherboard, controller or the wire integrator for one to many. If choosing the motherboard as the power supply, the light effect can be synchronize with MB.
*** Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product. ***
*** From 15th March 2018, all of our installation guides will be provided electronically via an easy-to-use QR code attached to the packaging. ***
*** Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test with only the pump connected to the power supply. ***
*** When using the leak tester on a water cooling loop, in order to avoid product damage due to excessive pressure, the input pressure should not exceed 0.5kg/cm2 (bar), and do not over 30 second. The leak tester must not be used when there is water in the loop or when the pump is running. If the product is damaged due to excessive pressure or incorrect use, Bitspower's product warranty will be null and void, and the cost of any damage to the hardware will be borne by the customer. ***
Last updated : 2021-07-13 08:20:07
No posts found